Views:

The haptic device drivers for the currently shipping versions of haptic devices to be used with Freeform & Freeform Plus software are available below for download. Select the appropriate file from the table and then follow these steps:

  1. Remove the previously installed haptic device driver from Control Panel, if any.

  2. ​Download the .exe file to your computer.

  3. Run the .exe file as administrator

Note:
1. Only one driver can be installed on a computer.

2. Touch Device Drivers support Ethernet & USB interface-based Touch devices. Phantom Device Drivers support all parallel port & FireWire interface-based PHANTOM devices.

Phantom Device Driver (PDD) installation guide

Geomagic Touch Device Driver (GTDD) installation guide


Freeform & Freeform Plus

v2019

Touch Device Driver v2018.10.22:

for Ethernet Geomagic Touch, Touch X, USB Touch or Touch X devices (Interface:   )

OS: 7/8/10 (64-bit)

 
Phantom Device Driver v5.1.9:

for Parallel devices (Interface:  )

OS: 7/8/10 (64-bit)

 

v2017

Touch Device Driver v2017.11.30:

for Ethernet Geomagic Touch devices (Interface:  )
OS: 7/8/10 (64-bit)

for USB Touch or Touch 3D Stylus (Interface:  )
OS: 7 (64-bit)

 
Geomagic Touch Device Driver v2016.10.13:

for Ethernet Geomagic Touch devices (Interface:  )
OS: 7/8/10 (64-bit)

for USB Touch 3D Stylus (Interface:  )
OS: 7 (64-bit)

 
Phantom Device Driver v5.1.9:

for Firewire or Parallel devices (Interface:   )

OS: 7/8/10 (64-bit) See important note for firewire devices*

 

v2016

Geomagic Touch Device Driver v2016.10.13:

for Ethernet Geomagic Touch devices (Interface:  )
OS: 7/8/10 (64-bit)

for USB Touch 3D Stylus (Interface:  )
OS: 7 (64-bit)

 
Phantom Device Driver v5.1.9:

for Firewire or Parallel devices (Interface:   )

OS: 7/8/10 (64-bit) See important note for firewire devices*

 

v2015

Geomagic Touch Device Driver v2014.20:

for Ethernet Geomagic Touch devices (Interface:  )
OS: 7/8 (32-bit & 64-bit)

for USB Touch 3D Stylus (Interface:  )
OS: 7 (32-bit & 64-bit)

 
Phantom Device Driver v5.1.9:

for Firewire or Parallel devices (Interface:   )

OS: 7/8/10 (64-bit) See important note for firewire devices*

 

v2014

Geomagic Touch Device Driver v2014.2:

for Ethernet Geomagic Touch devices only (Interface: )

OS: XP/7 (32-bit) and XP/7/8 (64-bit)

 
Phantom Device Driver v5.1.9:

for Firewire or Parallel devices (Interface:   )

OS: 7/8/10 (64-bit) See important note for firewire devices*

 
v2013 & v12 Phantom Device Driver v5.1.7:

for Firewire or Parallel devices (Interface:   )

OS: XP/Vista/7 (32 bit & 64 bit)

 
v10 & v11 Phantom Device Driver v4.2.131:

for Firewire or Parallel devices (Interface:   )

OS: XP/Vista/7 (32 bit & 64 bit)

 


 


Important Note:

IEEE-1394a compatible Firewire interface is supported for Win 7. However, Win 8 and 10 support is not guaranteed. Microsoft has dropped support for the components in the 1394 drivers which enable legacy mode, something that is often required to assure a particular card functions properly with Omni or PCC converters for parallel port devices.